paul_coin

I get that totally but still, if they keep climbing, a lot of us will have to redo or at least reconsider our electrical wiring and such. I run 30 amp circuits on 220v so I should be ok for a while but at the rate they…

I would like to see them produce smaller units - with half the hash and half the power consumption of these current new ones - this would be much easier to incorporate into my mining space. and its much less of a loss…

Does your app have the ability to reset to 0 with ambient and then where you turn on miner and get reading? If I set my phone on my desk at work, it reads anywhere from 45 to 62 dB - at home, where it is a bit more…

do your readings negate the ambient noise? and how close is your device doing the reading? I am laying mine essentially right against the miner but I also have ambient noise - it reads at almost 25 dB if the miner is…

I think the hard part is that I am not in a sound proof room with only the miner - so the readings have to be understood that ambient noise is also present. but that is also why I try and stick the mic right on the exit…

lol, note that is the loudest reading, and the meter is sitting right on the exhaust exit. It might be ambient noise too - I should take another reading with the Apollo off - here I will do so now - so look for an edit…

Will be doing setting 6 and 7 tonight update: my results for settings 6 and 7 posted above. due to the restarts at 700 mhz I set Target frequency to 690 and on setting 7 - will see if that will be stable.

RMA was completed and new miner came in and is up and running with zero issues after almost 4 hours of operation so far. Playing with voltage and freq settings presently. will update the post above as I try out…

maybe so, but I am setting up only one pool at a time.

I might - I switched it over to ViaBTC and it has had zero issues - so the pool may have been the issue.

In this post, I will be testing to see what the hash rate change is for each setting. Setting 0: Setting 1: Setting 2: Setting 3: Setting 4: with freq set to 750 in cg miner: - freq ramped up and I got the following…

I am currently running the miner on zpool to clean up some dust (about 10k) I will be doing this with at least a dozen pools before I eventually toss it on kano.is or maybe go solo on ckpool I realize this miner (along…

I placed an order with MineFarmBuy on August 17, and it was backordered at that time. They said it would be available in about a week. On August 23, I got a message saying it would ship on August 27 (but it actually…

Agreed, it is clear that layer 2 projects are very powerful and have been developing very rapidly in recent years. Trends metaverse, web3, NFTs I can't predict, their future is a question mark. But with layer 2 projects…

and wouldnt ya know it, bitcoin was over 10k for 3 straight days and all my coupons are expired but now btc is down - i think they have enough btc and cash to swing the market to make coupons all sadly expire right…

if the S9 cases work - i wonder how much it would be to just buy hashboards and controllers - without the existing case/psu - might be able to save some $ there. at you 3 board idea (i only chose 4 to be even but you…

imagine that - if you could bulk order cases - hmm would old s9 cases work for two boards? maybe make use of the shells and the old psu's - take the old hash boards and use for the projects like the Terminus.r606 which…

they should have an option to buy the miners with the number of hash boards requested by the buyer - example, if it has 4 boards and runs at 110 th with 3300 watts - why not let the buyer specify 2 boards to get 55 th…

I really hate the 3k watts - until I build a new warehouse, the current one cannot handle 3k watt miners without a complete rewiring. I guess I will just have to hope for getting some of the T17/S17 variants for cheap.…

Yes,yes exacly it's a small dca wallet proxy to hide bigger whale chains so nobody can't see so easy how much whales got funds and wich wallets more involved so weak hands don't join and strong floor holders joins first…