0xVault

What I'm trying to tell you is that the most commonly damaged parts are different for each different miner. The good news is that recently the zeusbtc Youtube channel released an introductory video for "Easily damaged…

Thanks for sharing. If this is true, I'm really sorry to hear the news. After reading your instructions, I searched for news about ComputeNorth. One of the articles said that nobody at computenorth.com has come up with…

Sadly the link to your firmware is dead, so I don't know if you have the correct firmware installed. It is stated in the latest firmware Whatsminer-M2x-all-20220511.19.bin on the Whatsminer website that if the miner…

I was wondering if you checked your power supply? If the power supply is in bad contact or aging, it will also cause the miner to restart during work.

Is your S9 PSU by APW3+ or APW3++? I found the specs for the APW3+. At this: https://www.zeusbtc.com/share/apw3-plus-12-1600w-power-supply/apw3-plus-specs.jpg

If you want to buy S19 Pro, you can contact the customer service of zeusbtc, all miners show "Get Quote".

I searched the specifications given by bitmain and found that the size of S19 Pro is smaller than that of S19a Pro, and the hash rate of S19 Pro is 110T and 105T, but the hash rate of S19a Pro is 110T, 106T and 102T. So…

If you want to know that the hash rate is the best, then it is undoubtedly Bitmain's S19 XP Hyd. The specifications show that its hash rate reaches 255T. But unfortunately, it is only pre-sale at present, and there is…

I have 1066, but currently, it's not working. If possible, I hope Avalon can give some related maintenance manuals, there are too few maintenances related to Avalon on the market. I want to buy a 1246 miner, but don't…

If you have replaced your T17+ heatsink with a one-piece heatsink, you can use thermal grease to connect the chip with the heatsink. Here is an introduction to how to use it: https://youtu.be/nUITyaE_aI4

I saw this module for the first time, but it doesn't look much different from the original S9 hash board, except that the positions of several triodes have changed. It can be seen that this is a repaired hash board,…

The state of the power supply appears to be normal. You need to check that your fan connectors and cables are well connected, the logs show 0 RPM for all 4 fans. Therefore, the temperature is abnormal and the operation…

Both GPU and ASIC miners support Bitcoin's proof-of-work SHA256 algorithm, but ASICs are more efficient.

There have been previous requests for the circuit diagrams of Whatsminer's power supplies, but good documentation is hard to find. I came across an article on zeusbtc on fixing Whatsminer power supplies, and I thought…

If you're fixing a hash board from the Avalon 10 series and your test equipment shows either 0 or some number, it doesn't matter if the C and CK signals look good or not. You can use the Avalon debug signal shorting…

If you want to know the function of the pins of the BM1397AG chip, you can check the repair manual of the T17+ or S17+ hash board, zeusbtc has many related repair manuals, and it is free. In these manuals, the function…

I saw this fan model you mentioned on the fan page of zeusbtc, but the title is Whatsminer fan M20S, I don't know if this is what you want? Because this fan is 6 pins. Regarding your fan wires always getting tangled up…

I'm not sure if I get what you mean. If you're trying to mix the 2 types of hash boards, I think something could go wrong. After all, the ASICs they use are not the same. If there is no suitable repair center in your…

I think maybe, but probably not that fast. The latest ASIC miners on the market currently use 5nm chips, and I'm looking forward to applying 3nm process technology to ASICs. According to reports, compared with the 5nm…

Not sure if you are still looking for a store for the S17 miner? At present, the Antminer 17 series miners are prone to the cooling fins falling off during transportation. So, if you want to buy S17, you can choose to…